Plate made of Epoxy resin paper for soldering capacitors, resistors, diodes ... in amplifier manufacturing projects. Its measurements are 258mm by 67mm and it has 189 holes to later place 2mm turrets.
Mallory 150 M Series capacitors are made of metallized polyester film with only a 5% tolerance. They are the condensers preferred by technicians the world over for their quality, performance and pure "vintage" sound. They are ideal for repairs, upgrades, or new projects on guitar or audio amplifiers.
Made in Russia. One of the best tubes you can buy for your amplifier or sound equipment now reissued by the New Sensor company. Excellent valve for its low noise level and couplings and for its musical details. Ideal to get a more British sound since, it reissues the vintage sound of the 60s quite clearly.
Valve manufactured by New Sensor in Russia (like Mullard ). This 12AX7 is very similar in characteristics to the Mullard 12AX7 with low noise, excellent tonal and harmonic response. Guaranteed results from the first moment!
Before the vacuum valves are shipped, they are tested with an Orange Valve Tester VT-1000!
New silicone rings ideal for valves that will prevent vibrations and noise.
Diameter: 30mm
Seven-pin mini sockets made with Micalex. Its manufacture and the use of top quality raw materials make this socket ideal for use in all types of hi-fi amplifiers, basses and guitars with small internal sizes. Not to be confused with Chinese imitations!
Made in the USA
Valves (Matched Pair) modeled after the one made by RCA 6L6GC, have more gain than the Sovtek 5881WXT (about 20% more). These tubes are one of the best 6L6s made today due to their low noise and microphony which gives them an excellent score for detail and harmonic content.
Rubber foot for heavy amplifiers, cabinets, effect pedals, dj's .... With steel insert. Diameter: 38mm. Height: 15mm. Hole diameter: 6.5mm. HIGH QUALITY FROM GERMANY!
New silicone rings ideal for valves that will prevent vibrations and unwanted noises.
Diameter: 20mm
If you know anything about Paul Reed Smith (PRS) guitars, you know there are a surprising number of possibilities available through the use of rotary switches. Further, you can use these for switching combinations within a pickup or between several pickups.
Clamping tube made of aluminum. Perfectly fits 12AX7, 12AU7, 6N2P and similar valves.
Made in the China.
5.5 cm long by 2.50 cm wide.
Potentiometer made in the United States by CTS for use in most brands of amplifiers made in the United States, especially in Fender amplifiers from the 70's. Its shaft is made of Nylon. A washer and a nut are included.
Measurements:
Total length - 26mm
Screw-in shaft length - 6mm
Total shaft length - 16mm
Base diameter - 23.5mm
Made in Slovakia. New and impressive quality for amplifiers and Hi-Fi equipment. Solid construction and rich details make this tube one of the best for preamp use.
Plate made of Epoxy resin paper for soldering capacitors, resistors, diodes ... in amplifier manufacturing projects. Its measurements are 300mm by 60mm with two rows of 30 turrets each.
Potentiometer made in the United States by CTS for use in most brands of amplifiers made in the United States, especially in Fender amplifiers from the 70's. Its shaft is made of Nylon. A washer and a nut are included.
Measurements:
Total length - 26mm
Screw-in shaft length - 6mm
Total shaft length - 16mm
Base diameter - 23.5mm
Capacitors of military origin that were used for military equipment of the former Soviet Union and that were rediscovered as one of the best capacitors for audio thanks to its good finish, its very precise specifications and its properties when used in guitars, basses, amplifiers of recognized brands, Danny Gatton, HI-FI equipment etc ...
Authentic and genuine pairs of AC176 and AC128 germanium transistors from Tungsram (NOS) brand. Ideal for building effects pedals like the Dallas Rangemaster, Tonebender, or for various Fuzz Face models. They also serve to repair old radios. Tested by a PEAK DCA55.
Valves of Soviet military manufacture manufactured between the years 1970 to 1979. They have almost the same performance as the western 12AX7 valve but be careful! The filament voltage goes to 6.3V and not 12V and you will have to modify them or buy an adapter for it.
Mallory 150 M Series capacitors are made of metallized polyester film with only 10% tolerance. They are the condensers preferred by technicians the world over for their quality, performance and pure "vintage" sound. They are ideal for repairs, upgrades, or new projects on guitar or audio amplifiers.
Black 5-position switch for Fender Stratocaster and Telecaster guitars. The hood is included as shown in the photos.
Excellent quality shielded and braided "Vintage" type cable to internally wire your Gibson guitar in the purest style of the 50's or 60's ("50's Wiring"). The cable can also be used to wire a combo or display or to make the typical old amp braided cable. Diameter is 0.070 "(1.78mm).
3PDT pushbutton with nine pins to "solder them to the air" for its use in modifications and repairs that demand this type of switches such as effects pedals, wah wah ...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k split shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s.
Comp Carbon Resistors with a tolerance of 5% at 0.5W. They have a low inductance and capacitance and are ideal for use in amplifiers or HI-FI equipment.
Sold in a pack of 5 units.
Deutsch
Español
English GB