2x VACUUM TUBE DAMPER FOR 6L6 6L6GC 6CA7 6SL7 TUBE AMPLIFIER

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

The Sovtek 5Y3GT tube is an indirectly heated full-wave rectifier tube intended for rectification in general purpose audio equipment. It has a 140 mA maximum output.

Valve manufactured by New Sensor in Russia (like Mullard ). This 12AX7 is very similar in characteristics to the Mullard 12AX7 with low noise, excellent tonal and harmonic response. Guaranteed results from the first moment!

Before the vacuum valves are shipped, they are tested with an Orange Valve Tester VT-1000!

A small resistance coil designed by Kent Armstrong which smooths out the signal and acts as a mid filter. Can be used in conjunction with a push / pull pot or a mini toggle 2 way switch to turn on and off.

Specs and Dimensions:

single wound 1.5 henries
Dimensions = 57/64 in. (23mm) X 47/64 in. (19mm)
Wire lead length = 1 11/64 in. (30mm)

LAST UNITS FOR SALE! IT IS THE MOST SEARCHED CAPACITOR BECAUSE THE BEING 400V GIVES A MORE SPECIAL TONE THAN THOSE OF 200, 630 OR 1000 VOLTS. THERE ARE FEW UNITS WORLDWIDE.

New silicone rings ideal for valves that will prevent vibrations and unwanted noises.

ON REQUEST! ESTIMATED DELIVERY 5 TO 21 WORKING DAYS.

Perfect copies of the legendary XF2 Mullard EL34 tube from the 60s. It is the perfect tube for the Dynaco ST-70 and for vintage Marshall brand amps although they can be used in all types of current amps. 100% British sound with low noise, good details and excellent sound and performance. One of the best EL34s on the market from a mythical brand.

5-position white switch for Fender Stratocaster and Telecaster guitars. The screws and the hood are included (it is white but has a slight yellow hue) as shown in the photos.

Rubber foot for heavy amplifiers, cabinets, effect pedals, dj's .... With steel insert. Diameter: 20mm. Height: 9mm. Hole diameter: 3.3mm. HIGH QUALITY FROM GERMANY!

Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k solid shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Solid shaft for push-fit knobs.

Potentiometer of the brand Alpha mini version special for those guitars with little depth or with little gap between components and cables. It can also be used on effects pedals, amplifiers, or other musical devices.

Vacuum valve manufactured by JJ Electronic in Slovakia. Robust valve manufactured according to the standards of the old ones, harmonically it is not very rich but it has a slightly higher gain than normal and a low noise level. If you don't want to spend a lot of money this could be your vacuum valve.

Clamping tube made of thinner aluminum and of better quality than the generic ones that will make the heat of the valve dissipate more easily and thanks to it it will work much better. Perfectly fits 12AX7, 12AU7, 6N2P and similar valves.

Made in South Korea.

5.5 cm long by 2.50 cm wide.

Silicone rings ideal for valves that will prevent vibrations and noise.

Diameter: 40mm

New silicone rings ideal for valves that will prevent vibrations and unwanted noises.

Diameter: 20mm

Super switch manufactured by Fender for use in various models of the brand and even for other manufacturers. Exceptional quality with zero noise. It is shipped in its original bag with two "tip caps" or hoods. Path Number: 0992251000. Made in Mexico.

The best push-pull potentiometer ever made! These aren't your standard off the shelf CTS pots either. Mojotone had them custom made to their specification to have the smoothest taper possible and the tightest tolerance available!

Excellent quality monofilament cable with YELLOW cotton coating "Vintage" type, to wire any brand of guitar or bass on the market: Fender , Gibson , Ibanez , Jakson, Rickenbacker ... The cable can also be used to wire a combo or a screen or to make the typical old amp braided cable.

Rock solid valve capable of handling high voltages. With the JJ 6V6s you will never have to look for NOS valves again, because it is designed like the old ones and even improved giving a sound from Blues to Rock with spectacular results that makes it one of the best 6V6s on the market by far.

5 original Switchcraft brand nuts to use on various models of their jacks. They can also be used in potentiometers made in the United States or Canada ( CTS , Bourns , PEC ..) because they are American metric although the pressure washers (Lockwasher) would be missing.

8-pin socket for valves type EL34, KT88, 6L6, 6V6, KT66, 6550 ... made of authentic BAQUELITE for military use in the former Soviet Union. If you want quality and good sound this is your socket. Do not play it!

The best kit to not lose treble when you lower the volume of your guitar! This kit is comprised of premium grade electronic components (NOS) made in the United States and the former Soviet Union: a K40Y-9 680pF capacitor and a 150k 1 / 2W Allen Bradley resistor. This kit is designed in the style of Acme Guitar Works (in parallel).

PRODUCT UNDER ORDER! ESTIMATED DELIVERY TIME: 5-31 DAYS.

The perfect vacuum tube for Fender Tweed Champ and Deluxe amps! This model withstands high voltages very well and the best existing materials have been used to recreate the classic 6V6 of a lifetime.

K40Y-9 680pF paper-in-oil or PIO capacitor made in the former Soviet Union. Ideal for use in various electronic projects including "volume treble bleed" or treble bleed.

New fittings ideal for valves that are inserted into chassis that face downwards that will avoid unwanted vibrations and noise. They fit perfectly with EL34, 6V6, 6L6, 5881 valves and the like.

In the words of the manufacturer: "Smooth, velvet-like sound. Vintage-vibes galore, great upgrade for Fender s lacking that special kick."