ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6FM7 is a compactron dissimilar double triode designed for used as a combined vertical-deflection oscillator and amplifier in television receivers. Section one, a high-mu triode, is intended for service as an oscillator; section two, a low-mu, high perveance triode, for service as an amplifier.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

¡BAJO PEDIDO! ¡ENTREGA ESTIMADA DE 5 A 31 DÍAS! 

Full Wave Tube Rectifier

¡BAJO PEDIDO! ¡ENTREGA ESTIMADA DE 5 A 31 DÍAS! 

5Y3GT  NOS USA

Various brands, mostly made by Sylvania and CBS.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 5750 is a miniature pentagrid converter designed for use as a combined mixer and oscillator in superheterodyne circuits. Analysis of the electrical characteristics of this tube with those of the 6BE6 will indicate that the 5750 is essentially similar. The 5750 is a special-quality tube intended for use in critical industrial and military applications in which operational dependability is of primary importance.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1LC6 is a filament-type pentagrid converter designed particularly for use in low drain battery-operated equipment. This tube will operate satisfactorily with only 45 volts B supply.

Also known by US military identifier VT-178.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 5670 is a miniature medium-mu twin triode each section of which as a separate cathode connection. The tube is suited for use in a wide variety of general-purpose amplifier and mixer circuits as well as numerous multi-vibrator and oscillator applications. The useful operating range extends from low frequencies through the VHF region.

The 5670 is a special-quality tube intended for use in critical industrial and military applications in which operational dependability is of primary importance. Features of the tube include a high degree of mechanical strength and a heater-cathode construction capable of withstanding many-thousand cycles of intermittent operation. When used in on-off control applications, the tube will maintain its emission capabilities after long periods of operation under cutoff conditions. Analysis of the electrical characteristics of this tube with those of the 2C51 will indicate that the 5670 is essentially similar.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 3S4 is a filamentary type power output pentode in the miniature construction. It is characterized by economy of filament power and ability to perform well at low plate supply voltages such as encountered in portable equipment.

Also known by US military identifier VT-174.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12AV5GA is a beam pentode using either a T-11 or T-12 bulb. It is designed for use as a horizontal-deflection amplifier in 600 mA series heater operated television receivers. Thermal characteristics of the heater are controlled such that heater voltage surges during the warm-up cycle are minimized provided it is used with other types which are similarly controlled.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 5965-A is a miniature twin-triode primarily designed for service in computer applications. Each triode section features a high zero-bias plate current, a sharp-cutoff characteristic, and a separate cathode connection. In addition, the balance of the cutoff characteristic between the two sections is controlled. When used in "on-off" control applications, the 5965-A will maintain its emission capabilities after long periods of operation under cutoff conditions. The heater-cathode construction of the tube is designed for dependable service under conditions of intermittent operation.

The 5965-A, when operated under approved conditions, will exhibit a life of greater than 10,000 hours, averaged over a 100 tube lot, and based on the 10,000 hour end-of-life point shown under Special Tests and Ratings.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Our favorite for 2x 6L6GC/5881/7581a/KT66 amps traditonally made on paper bobbin in Illinois, USA. 

Secundary 2, 4 + 8 Ohm, max. 70 Watts

(replaces/upgrades 125A9A, 45249, 022855, 125A13A, 022871). 

Superior tone with paper layer design. 

Perfect upgrade for:

- Fender Bassman '59

- Fender Bassman LDT

- Fender Super Reverb (45W Version AB763 etc.)

- Fender Vibroverb (45W Version AB763 etc.)

- Fender Concert II (Fender 'Rivera' Series 1980er Jahre)

- Fender Hot Rod DeVille (direct replacement for 004-1754-000)

- Fender Blues DeVille  (direct replacement for 004-1754-000) 

The 018343 is used in several TAD Amp Kits like 5F6 Bassman, 5E8 Low Power Twin, BF Super Rev, BF Vibroverb (subject to change). 

Replacement for the 125A13A (022871) für den Fender® Bassman 50, 6G6A, 6G6B, 50W.

Also perfect for Mesa Boogie MK I, MK II, MK III with 60W (562060)

Replaces the 560039 transformer of the Acoustic G60T and Mod 162.

Spare part for the TF125 in the Hughes&Kettner TUBE 50

Primary impedance 4.2k

Lamination: 3 3/4", Stack: 1 1/4"

Mounting on: 3 1/4" x 2"

Overall dimensions: W x H x D: 96mm x 79mm x 80mm

Primary:       

      A1      Blue

      HT      Red

      A2      Brown

Secondary:

      0 Ohm      Black

      2 Ohm      White

      4 Ohm      Yellow/Green

      8 Ohm      Green

Transformator Type: Output Transformers

Stack: EI96(3.75 Inch)

OT-Tubes: 6L6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Reverb drive Transformer, suitable for allmost all Fenders since 1964(= 022921). 

Custom made for TAD in the USA!. 

primary used by all Fender® models with tube reverb from 1963-1990 and Reissue models like:

Fender® Princeton Reverb

Fender® Deluxe Reverb

Fender® Vibrolux Reverb

Fender® Pro Reverb

Fender® Super Reverb

Fender® Twin Reverb

Fender® Quad Reverb

Fender® Super Six Reverb

Fender® Vibrosonic

Fender®`65 Princeton Reverb Reissue

Fender®`65 Deluxe Reverb Reissue

Fender®`64 Custom Deluxe Reverb Amp

Fender®`65 Super Reverb Reissue

Fender®`65 Twin Reverb Reissue

Fender®'65 Twin Custom(TM) 15

Fender® Prosonic 

Replaces also the 037099 of the `63 Vibroverb Reissue

Also suitabel for Mesa Boogie® #550185

For the Fender®`63 Reverb Unit Reissue please order the 004-7605-000

Mounting center:  43mm

ca. 25kOhm to 8 Ohm

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Reverb drive Transformer, suitable for allmost all Fenders since 1964(= 022921). 

Custom made for TAD in the USA!. 

primary used by all Fender® models with tube reverb from 1963-1990 and Reissue models like:

Fender® Princeton Reverb

Fender® Deluxe Reverb

Fender® Vibrolux Reverb

Fender® Pro Reverb

Fender® Super Reverb

Fender® Twin Reverb

Fender® Quad Reverb

Fender® Super Six Reverb

Fender® Vibrosonic

Fender®`65 Princeton Reverb Reissue

Fender®`65 Deluxe Reverb Reissue

Fender®`64 Custom Deluxe Reverb Amp

Fender®`65 Super Reverb Reissue

Fender®`65 Twin Reverb Reissue

Fender®'65 Twin Custom(TM) 15

Fender® Prosonic 

Replaces also the 037099 of the `63 Vibroverb Reissue

Also suitabel for Mesa Boogie® #550185

For the Fender®`63 Reverb Unit Reissue please order the 004-7605-000

Mounting center:  43mm

ca. 25kOhm to 8 Ohm

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 50A5 is a beam power amplifier designed primarily for use in the output stage of a-c/d-c receivers. The 50A5 features high power sensitivity and high efficiency when operated at relatively low plate and screen voltages.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 7Z4 is a heater-cathode type high vacuum twin diode using the lock in construction. It is intended for power rectifier service in AC operated equipment or for use with storage battery and vibrator in automotive receivers or amplifiers.

Also known by US military identifier VT-181.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6CS7 is a miniature double triode having dissimilar sections. Section no. 1 is intended for operations as a vertical deflection oscillator and section no. 2 as a vertical deflection amplifier.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 5654 is a miniature sharp-cutoff pentode for use as a wide-band, high-frequency amplifier. It is also useful in video and audio amplifiers, oscillators, mixers, frequency multipliers, and cathode followers. The 5654 is a special quality tube intended for use in critical industrial and military applications in which operational dependability is of primary importance. Features of this tube include a high degree of mechanical strength and a heater-cathode construction capable of withstanding many thousand cycles of intermittent operation. When used in on-off control applications, the tube will maintain its emission capabilities after long periods of operation under cutoff conditions. Analysis of the electrical characteristics with those of the 6AK5 will indicate that the 5654 is essentially similar.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1LH4 is a tube combining a single diode and a high-mu triode in one bulb. It is designed for service as a diode detector, AVC rectifier, and as a resistance coupled amplifier.

Also known by US military identifier VT-177.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6SA7GT is a pentagrid converter. It is intended to perform the combined functions of the mixer and oscillator in superheterodyne receivers, especially those of the all-wave type. The 6SA7GT is constructed to provide excellent frequency stability.

Also known by US military identifier VT-150A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1A7GT is a filament type pentagrid converter designed for service as a combined mixer and oscillator tube in low drain battery operated equipment.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6H6 is a twin-diode with individual cathodes brought out to separate base pins. The 6H6 is designed for service as a diode detector, automatic volume control rectifier, or as a low current power rectifier.

Also known by US military identifier VT-90A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

117Z3 - Rectifier, Half Wave Heater, for unipotential cathode. 117 volts AC-DC.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6H6GT is a twin-diode with individual cathodes brought out to separate base pins. The 6H6 is designed for service as a diode detector, automatic volume control rectifier, or as a low current power rectifier.

Also known by US military identifier VT-90A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

Twin diode, medium-mu triode. 7-pin miniature type for use in automobile-radio receivers operating directly from 12-volt storage batteries.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

Pentode for use as RF, IF, or video amplifying valve or mixing valve in television receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

Pentode for use as RF, IF, or video amplifying valve or mixing valve in television receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

Voltage-reference tube, 7-pin miniature, glow-discharge type. Especially useful as a voltage reference tube in DC power supplies.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6100 / 6C4WA is a heater-cathode type medium-mu triode of miniature construction, suitable for use as a class C amplifier and oscillator. This type is characterized by long life and stable performance. It is designed for service where conditions of high temperature and mechanical shock or vibration are encountered.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transformer for: Fender® Twin Amp, Bj. 58-60, 4x6L6/5881, 4 Ohm for High Power Tweed Twin, Twin Amp 5F8 - 6G8-A (= 125A4A). 

Custom Made for TAD with high grade M6 laminations. 

Grand Stack =  big tone!!!! Attention: high induction, only to be used with low B+ voltagesd up to 450V! 

Overall dimensions:  W x H x D: B x H x T: 96 x 83 x 117 incl. shrouds. 

Mounting on 78mm x 92-96mm 

Impedance: ca. 2.1k Ohm P-P 

Primary:                  

      A1            Blue

      B+            Red

      A2            Brown                  

Secondary:                  

      4 Ohms            Green

      0 Ohms            Black

Transformator Type: Output Transformers

OT-Tubes: 6L6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Grand-Stack version with fatter Stack (1") Increases Punch und Bass! 

2x 6V6GT to 4, 8 Ohms 

Improved Version 

CUSTOM MADE IN USA, Paper bobbin wound! 

Upgrade also for the Fender Deluxe Reverb® Reissue and the 64`Custom Deluxe Reverb® Amp (replaces 004-1318-000; 041318).

We recommend this OT for Fender 65`Princeton Reverb® style amps as well, and the auch passend für den Fender Supersonic 22.

The 125A1A-GS also has considerably more iron compared to the 125A1A (022918; 125A10B; 002-2918-000), but fits most chassis without any problems.

Only an additional 3mm mounting hole has to be drilled. Beyond that, no further modifications are required!

The extra iron gives the sound more power and punch without losing definition and complexity. 

Lamination: 2 5/8"      Stack: 1" 

Primary impedance ca. 6.7kOhm

Mounting on 3,125" 

Primary:

      A1      Blue

      B+      Red

      A2      Brown 

Secondary:

      8 Ohms      Green

      4 Ohms      Yellow

      0 Ohms      Black

Transformator Type: Output Transformers

OT-Tubes: 6V6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

UPGRADE: OUTPUT TRANSFORMER for Fender Blues Junior, Hot Rod Series, 15W, 4, 8 + 16 Ohms

Upgrade: stacking is 1". 

Impedance ca. 7k p-p 

Primary:            

      A1      Brown

      B+      Red

      A2      Blue            

Secondary:            

      16 Ohm       white

      8 Ohm      green

      4 Ohm      yellow

      0 Ohm      black 

Please swap blue and brown for correct operation!. 

Fits also Fender Musicmaster Bass!

Transformator Type: Output Transformers

Stack: 2.25 Inch

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

UPGRADE: OUTPUT TRANSFORMER for Fender Blues Junior, Hot Rod Series, 15W, 4, 8 + 16 Ohms

Upgrade: stacking is 1". 

Impedance ca. 7k p-p 

Primary:            

      A1      Brown

      B+      Red

      A2      Blue            

Secondary:            

      16 Ohm       white

      8 Ohm      green

      4 Ohm      yellow

      0 Ohm      black 

Please swap blue and brown for correct operation!. 

Fits also Fender Musicmaster Bass!

Transformator Type: Output Transformers

Stack: 2.25 Inch

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6JM6A is a duodecar type used as a horizontal-amplifier tube in color and black-and-white television receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 0A2WA is a cold cathode, gas-filled diode of miniature construction designed for reliable service as a voltage regulator. It has an operating current range of 5 to 30 milliamperes over which it maintains a substantially constant operating voltage of 150 volts. Three cathode pins are provided which may be used to disconnect the load when the tube is removed from the socket. This type is characterized by long life and it is designed for service where severe conditions of high temperature and mechanical shock or vibration are encountered.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12SG7 is a semi-remote cut off pentode voltage amplifier in the octal metal construction. It features high transconductance with low grid-plate capacitance and a dual cathode connection to minimize effects of common cathode circuit coupling.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6ER5 is a semi-remote cutoff, frame grid triode designed for use as a VHF RF amplifier. Features of the design include a partial shield between the grid and plate which lowers the capacitance between these two elements and promotes ease of neutralization and higher input impedance by virtue of dual cathode leads.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12AU6 is a pentode amplifier having a sharp cut-off control characteristic using the miniature construction. With high transconductance, low grid-plate capacitance, it is intended for service as either an RF or AF amplifier. Except for heater ratings, the 12AU6 is identical to the 12AU6.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 0B2 is a two-electrode, inert-gas-filled cold cathode miniature tube intended for use as a voltage regulator. The tube has a maintaining voltage of approximately 108 volts over a current range of 5 to 30 mA. The 0B2 is excellent for applications which require good voltage regulation and long life.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 3A5 is intended for use in high frequency applications. The relatively large filament employed in the 3A5 enables it to supply the high peak currents required in RF power applications. In class C service, a 3A5 with its units in push-pull will deliver a power output of approximately 2 watts at 40 megacycles. It may be used at still higher frequencies with reduced efficiency. Each triode may be used independently of the other.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6SK7GT is a remote-cutoff pentode. It is designed for use as a high-gain radio-frequency or intermediate-frequency amplifier in a radio receiver. Because of its remote-cutoff characteristic, this type will handle large signal voltages without cross-modulation or modulation-distortion and is suitable for use in receivers which employ automatic-volume-control.

Also known by US military identifier VT-117A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 7A7 is a pentode voltage amplifier using the lock-in construction. It is designed for RF or IF service in AC/DC receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 36AM3B is a half-wave rectifier in the 7 pin miniature construction. Features of the tube are a 100mA. heater with 20 second warm-up time. It has a heater tap section (pins 4 & 6) that may be used as a limiting resistance in the rectifier plate circuit or as a panel lamp shunt.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6BZ6 is a miniature semi-remote-cutoff pentode designed primarily for use as an intermediate frequency amplifier in television receivers. Its semi-remote-cutoff characteristic makes the tube particularly useful in stages to which it is desired to apply automatic-gain-control. The tube also features a high transconductance and relatively low interelectrode capacitances.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6Q7 combines two diodes and a high-mu triode in a single envelope, using a common cathode. It is designed for service as a diode detector, AVC rectifier, and as a high gain resistance coupled amplifier in AC, storage battery, and AC - DC operated receivers.

Also known by US military identifier VT-92.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6K7GT is an indirectly heated pentode of the vari-mu (remote cut-off) type for use in the RF or IF stages of radio equipment.

Also known by US military identifier VT-86B.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12K7GT is a variable-mu pentode amplifier in the octal glass construction. It is suitable for use with AVC in RF and IF amplifier and minimizes cross modulation.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6L7 is a mixer tube designed for service with a separate oscillator as the first detector in superheterodyne receivers. The control grid is of the remote cut-off type which allows the use of AVC and minimizes cross-modulation. The control grid is of the sharp cut-off type. The tube may be used as a volume expander or as a doubly controlled general purpose amplifier.

Also known by US military identifier VT-87.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 35Z3 is a half-wave high-vacuum rectifier designed for use in a-c/d-c receivers. Electrically the 35Z3 is equivalent to the 35Z5GT except that the heater of the 35Z3 is not tapped for operation of a panel lamp. The 35Z3 is a loctal-based tube (compared to the octal base of the 35Z5GT.).

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

Want to change the look of your Stratocaster® without spending a lot of money on a paint job? Try sprucing it up with a Stratocaster Accessory Kit. Everything you need to personalize your Stratocaster.

Includes volume and tone knobs, tremolo arm tip, switch tip, tremolo backplate and pickup covers.

Pickup covers will not fit SCN™, N3™, or Noiseless™ pickups.

Package contains 3 Pickup Covers, 3 Knobs, Backplate, Pickup Switch Tip, Tremolo Arm Tip.

Want to change the look of your Stratocaster® without spending a lot of money on a paint job? Try sprucing it up with a Stratocaster Accessory Kit. Everything you need to personalize your Stratocaster.

Includes volume and tone knobs, tremolo arm tip, switch tip, tremolo backplate and pickup covers.

Pickup covers will not fit SCN™, N3™, or Noiseless™ pickups.

Package contains 3 Pickup Covers, 3 Knobs, Backplate, Pickup Switch Tip, Tremolo Arm Tip.

Want to change the look of your Stratocaster® without spending a lot of money on a paint job? Try sprucing it up with a Stratocaster Accessory Kit. Everything you need to personalize your Stratocaster.

Includes volume and tone knobs, tremolo arm tip, switch tip, tremolo backplate and pickup covers.

Pickup covers will not fit SCN™, N3™, or Noiseless™ pickups.

Package contains 3 Pickup Covers, 3 Knobs, Backplate, Pickup Switch Tip, Tremolo Arm Tip.

Want to change the look of your Stratocaster® without spending a lot of money on a paint job? Try sprucing it up with a Stratocaster Accessory Kit. Everything you need to personalize your Stratocaster.

Includes volume and tone knobs, tremolo arm tip, switch tip, tremolo backplate and pickup covers.

Pickup covers will not fit SCN™, N3™, or Noiseless™ pickups.

Package contains 3 Pickup Covers, 3 Knobs, Backplate, Pickup Switch Tip, Tremolo Arm Tip.

Fender offers a wide selection of Pure Vintage electronics to players looking to restore or upgrade their guitar or amplifier with classic Fender in mind. From potentiometers to select capacitors, tube sockets and more, these electronics are created to closely replicate original-era Fender parts and have been used on a number of Fender reissue instruments and amplifiers, including our American Vintage series of guitars and basses. But best of all, Pure Vintage guitar and amp electronics are also versatile enough to fit most Fender guitars and tube amplifiers, making it easier than ever to inject that vintage vibe into any setup.

Pure Vintage Wax Paper Capacitor, .10uf @ 150V

Replicas of original-style capacitors

Wax paper construction for warm vintage tones

Used in tone circuit of vintage Stratocaster, Telecaster, Jazz Bass, Precision Bass guitars...

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6K5GT is a cathode type high mu triode designed for use in high gain resistance coupled circuits. This tube has a lower amplification factor than previous similarly designed triodes thus enabling the use of a large signal input both under 250 volt and 100 volt operating conditions. The value of grid bias can be less critical than with a tube having a higher amplification factor.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 50BM8 is a miniature type triode-pentode designed for use as an AF amplifier by triode section and AF power amplifier by pentode section in radio receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1R5 is a miniature pentagrid-converter designed for use as a combined mixer and oscillator in superheterodyne circuits. Because of its small size and high operating efficiency, the 1R5 is especially adapted for compact, battery-operated equipment.

Also known by US military identifier VT-171.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 7695 is a beam power pentode featuring a remarkably high power sensitivity as an audio power amplifier. In Class A1 operation, it can deliver 4.5 watts of power with a B+ voltage of only 130 volts. As a result, the 7695 makes possible economies in power supply requirements.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6J11 is a compactron device containing two sharp cutoff pentodes, designed primarily for intermediate-frequency amplifier service in television receivers.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12B4-A is a miniature low-mu triode designed primarily for service as a vertical-deflection amplifier in television receivers. The tube features high plate current at relatively low plate voltages and is capable of withstanding the high pulse voltages normally encountered in this application. In addition, the 12B4-A exhibits a controlled heater warm-up characteristic which makes the tube particularly suited for use in television receivers which employ series-connected heaters. When the 12B4-A is used in conjunction with other 600-millampere types which exhibit essentially the same heater warm-up characteristic, heater voltage surges across the individual tubes are minimized during the warm-up period.

Except for the controlled heater warm-up time characteristic, the 12B4-A is identical to the 12B4.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6Y6G is a beam power amplifier having high power sensitivity and high power output at comparatively low DC supply voltages.

Also known by US military identifier VT-168A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1N5GT is a filamentary type sharp cut-off pentode voltage amplifier. It is designed for service in low-drain battery-operated receivers as an RF, IF, or AF amplifier.

Also known by US military identifier VT-146.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12J5GT is a general purpose medium-mu triode. It is useful for service as an oscillator or audio-frequency amplifier.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6AX5GT is a full-wave rectifier of the heater-cathode type intended for use in AC operated and automobile receivers. Because of its heater-cathode construction it has the same heating time as that of other heater-cathode types in the receiver. Use of this tube prevents excessive voltages from appearing across filter condensers during warm-up period.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

The perfect item for your Fender Twin Reverb Amplifier to tweek to real '65 blackface specs PLUS having the luxury of providing an additional 8 Ohm secondary for being more flexible regaing the speakers connected to your amp.

This transformator is also used in the 100W Fender Showman Reverb, Quad Reverb and Vibrosonic Reverb.

(=022889 + 022897)and PA100 (022889/125A29A)

Does also fit in ´65 Fender® Twin Reverb Reissue (replaces 037612) and the Blackface Single Showman as a replacement for the 125A30A. 

Direct Replacement for Mesa Boogie MK I, MKII. replaces 562100

Also used by Jim Kelly: 4x 6V6 to 8/16 Ohms!

Fits Acoustic 100W Amps also: GT100 etc. replaces 560033 

Impedance ca. 2k

Mounting on 3 7/32" x 2 7/32" 

Made in USA / Paper Stick Wound 

primary   

 A1  blue

 HT  red

 A2  brown   

secondary   

 0 Ohm  black

 4 Ohm  green

 8 Ohm  yellow 

Does not fit Fender Amps with 135W RMS (see speaker output jack) if so please use the 013691 transformer!

Transformator Type: Output Transformers

OT-Tubes: 6L6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transformer for: Fender® Tweed Super 5F4, Pro 5E5A, Bandmaster 5E7,   4+8 Ohms , Paper Bobbin, correct impedance.

CUSTOM MADE FOR TAD IN THE USA! 

Can be used also for the 45217 like used in the Fender Vibrolux 6G11 and Bandmaster 6G7-A. 

Overall dimensions:  W x H x D: 102,5 (incl. Lug) x 65,5 x 67 mm. 

Mounting on 90.5mm. 

Lamination: 3", Stacking 1,25" 

Impedance: ca. 6k Ohm P-P

power handling: 40 Watts. 

Primary:            

      A1      Blue

      B+      Red

      A2      Brown            

Secondary:            

      8 Ohms      Yellow

      4 Ohms      Green

      0 Ohms      Black

Transformator Type: Output Transformers

Stack: 3 Inch

OT-Tubes: 6L6

OT-Impedanz: 4+8 ohms

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

OUTPUT TRANSFORMER  for 4x 6L6GC  135W  4/8 Ohm UltraLinear Type (with screen grid taps), max. 135W 4/8 Ohm.

UPGRADE for the transformator used in the 1975-1980 built 135W Fender Twin Reverb, Showman Reverb, Quad Reverb, Vibrosonic Reverb and in the Bassman 135.  Also used in the Fender 140. 

Lamination 3 3/4", Stacking: 1 3/4" 

Superior M6 lamination quality. 

Mounting on 70-75mm x 80mm 

Primary:            #70005

      A1      Blue (Blue)

      Tap1      Purple (Blu-Yel)

      HT (B+)      Red (Red)

      Tap2      Yellow (Brn-Yel)

      A2      Brown (Brown) 

Secondary:

      0 Ohm      Black

      4 Ohms      Green/Yellow

      8 Ohms      Yellow 

Colors in brackets denotes original wires.

Transformator Type: Output Transformers

OT-Tubes: 6L6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

2x 6V6GT  , aprox. 18 Watt with 4, 8 and 16 Ohms

traditionally made with authentic materials and paper bobbin. 

Made in USA - vintage correct paper bobbin wound for superior tone!

Exactly made after original specs for the 1957-1959 Fender 5E3 Deluxe amp but with additional 4 + 16 Ohms tabs to allow propper connecting to alternative speaker set-up and various external cabinets. 

NEW: with increased stack (1") for tight and superior bass response. 

Mounting on 3 1/8" 

Overall Dimensions:      W x H x D:            93,5mm x 58mm x 58mm incl.

Zaa ca. 8k Ohm 

Primary:            

      A1      Blue

      B+      Red

      A2      Brown            

Secondary:            

      16 Ohms      Orange

      8 Ohms      Green

      4 Ohms      Yellow

      0 Ohm      Black

Transformator Type: Output Transformers

OT-Tubes: 6V6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transformer SE (single ended) 1x6V6, 4Ohms, 5W

for Tweed Champ. 

US-MADE, paper stick bobbin! 

secondary impedance : 4 Ohms

primary impedance: 8.2k Ohm

primary current: max. 35mA

Mounting on: 2" 

W x D x H: 1 11/16" x 1 13/32" x 1 3/8" 

matching recommended speakers:

Jensen P8R, P10R-4, P12R-4, C8R and CH1270-4 

primary:

      HT            blue

      A            red 

secondary:

      0 Ohm            black

      4 Ohm            green

Transformator Type: Output Transformers

OT-Tubes: 6V6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transformer for: Fender®Blues Deluxe (NOT Reissue !!!) 2x 6L6, 4 und 8 Ohm, 40W. US-Made. 

ca. 4.3k Ohm 

Lamination: 3" 

mounting on 90.5mm 

The Output transformer for the Fender®Blues Deluxe REISSUE can be found at "more matching products and alternatives". 

Primary:            

      A1      Blue

      B+      Red

      A2      Brown            

Secondary:            

      8 Ω      Green

      4 Ω      Yellow

      0 Ω      Black

Transformator Type: Output Transformers

OT-Tubes: 6L6

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 7062 is a special quality double triode designed for use in computer circuits.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transf. for Fender Bassman Ten

2x6L6GC   8   Fender Bassman Ten 

Only for 50W models without Screen taps!

For Fender Bassman Ten 70W models with screen taps please use the 013897 output transformer. 

Lamination: 3", Stack 1 5/8"

Mounting on 64mm x 58mm. 

primary impedance ca. 5.3k 

dimensions: W x H x D: 78mm x 65mm x 87mm 

Custom Made for TAD 

Primary:

      A1      Blue

      HT      Red

      A2      Brown 

Secondary:

      0 Ohm      Black

      8 Ohms      Green

Transformator Type: Output Transformers

Stack: 3 Inch

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Output transformer for 2x6L6GC/5881  4 + 8 Ohm / max. 50 Watt

Exact Transformer for Fender blackface and silverface models: Bandmaster, Bandmaster Reverb (fits TFL5005D also), Pro Amp (8 Ohm), Pro Reverb Amp, Vibrolux (8 Ohm), Vibrolux Reverb, Tremolux (all schematic type AA763+AB763+AA1069). Fits also brownface Vibrolux 6G11-A.

Also replaces Fender P/N 036968 + 125A7A / 022848.

Made in USA with vintage correct paper bobbin wound with superior tone!

Primary impedance: 4.2K

Mounting: 90.5mm

Primary                  

      A1            blue

      HT            red

      A2            brown                  

Secondary                  

      0 Ohm            black

      4 Ohm            yellow

      8 Ohm            green

Transformator Type: Output Transformers

OT-Tubes: 6L6

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Mains transformer for: Fender® Tweed Bassman (5F6-A), Tweed Pro Amp (5E5-A), Tweed Bandmaster (5E7), Tweed Twin (5E8 "Low Power"), Super (5F4, 6G4, 6G4-A). 

Lamination 4 1/8" , Stacking 1 3/4" 

Mounting on 87.5mm x 70mm. 

Dimension: L x W x H: 105mm x 88mm x 100mm 

Primary:                  

      240V            Brown

      230V            Black

      220V            Grey

      0V            White                  

Secondary:                  

      345V@200mA      Red

      52V            Blue

      0V            Green/Yellow

      345V            Red                  

      3,15V@5.5A      Green

      0V            Green/Yellow

      3,15V            Green                  

      5V@6A            Yellow

      0V            Yellow

PT-Secondary: incl. 5V winding (for Rectifier)

Transformator Type: MainTransformer

Stack: EI105(4.125 Inch)

Additional winding to 230V (primary): 240V

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Transf. Mains for Fender Champ 25 SE and Champ 25. 

Lamination: 3", Stack 2" 

Dimensions: L x W x H: 76mm x 64mm x 93mm

Installation height: 80mm 

Fits Laney AOR30 also!

(increase R75 , R76, filament balance with 2x100R). 

Also perfect for DIY projects up to 25W. Match the chassis K-ACPRV! 

NEW: Comes with top shround and supports all primary voltages of the original! 

Original colors and connection points for 220-240V in brackets:

Primary:                  

      0V            Orange (BLK/RED - CP3)

      120V            Purple (BLK/GRN - CP20)                  

      0V            Grey (BLK/YEL - CP21)

      100V            White (WHT - CP22)

      120V            Black (BLK - CP23)                  

Secondary:

      315V      180mA      Red (CP14)

      0V            Red (CP6)                  

      45V      50mA      Brown (CP7)

      0V            Brown (CP8)                  

      6,3V      2.5 A      Green (CP18)

      0V            Green (CP13)                  

      19V      300mA      Blue (CP16)

      0V            Yellow (CP10)

      19V            Blue (CP17)

Stack: 3 Inch

Additional winding to 230V (primary): 110V-120V

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

The 125P34AX (=022764) is the Export-Version and replaces the 110V US-Version 125P34A (=022756).

CUSTOM MADE in U.S.A.

These transformers are made in the USA. Quality, reliability, and excellence are what make our transformers the best around.

This is the perfect mains transformer for all 80W Blackface (AB763) and 100W Silverface Fender Amps like the Fender Twin Reverb, Fender Showman Reverb, Bassman 100, Vibrosonic Reverb but also used for the rare Jim Kelly Amps. 

NOTE: the 135 Watt Twin Reverb / Showman amp models (from mid 1970s to 80s) must use the 013830. 

Also used in the Mesa Boogie MK 1 (NO REISSUE!) and MK 2 Series with NO FAN!. 

For the Mesa Boogie MK 1 REISSUE and MK 2 Series WITH FAN the power transformer 561141 has to be used. 

Does not fit on `65 Fender® Twin Reverb Reissue: see transformer 037611. 

Comes without mounting nuts, originals will fit!

See also HR3121 as mounting nuts 

Lamination: 4 1/2" 

Primary:    

 0V            Black

 220V            Black/Yellow

 230V            Green/Black

 240V            Red/Black

Secondary:    

 340V@380mA      Red

 60V            Red/Blue

 0V            Red/Yellow

 340V            Red    

 3,15V@6A      Green

 0V               Green/Yellow

 3,15V               Green

Stack: EI114(4.5 Inch)

Additional winding to 230V (primary): 240V

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Mains transformer for Fender® 135W models: This 013830 is used for all 135 Watt Fender amps of the 1970s: Twin Reverb, Dual-Showman Reverb, Bassman 135, Quad Reverb and Vibrasonic Reverb.

Check the power output marked at the speaker jack at all 135 Watt models. 

Lamiantion: 4 1/2", 

Now with all voltage taps of the original 

Cutout needed : 83mm x 69mm 

Mounting on 95mm x 73mm 

Primary:                  

      0V            Black

      100V            White

      120V            Orange

      127V            Grey

      220V            Yellow

      240V            Green

      260V            Red

Secondary:                  

      185V      600mA      Red

      0V            Yellow

      185V            Red                  

      56V      75mA      Brown

      0V            Brown                  

      6,3V      6A      Green/Yellow

      0V            Green 

NOTE: the earlier 100 Watt-Versions (since 1964- mid 1970s) use the 125P34AX mains transformer.

Transformator Type: MainTransformer

Stack: EI114(4.5 Inch)

Additional winding to 230V (primary): 110V-120V

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Transf.MAINS for: Fender® Tweed Deluxe Amp (5E3 etc.). 

NEW VERSION: 2" STACK and C.T. on filament for low noise

supports 6L6GC and GZ34/5AR4 tubes also! 

Lamination: 3 3/8"

Mounting on 70 x 56mm, lay-down. 

Height above chassis: 75mm

W x D x H: 87mm x 70mm x 90mm

weight: aprox. 2.2kg 

Primary:            

      0 V      Black

      230 V      White

      240 V      Grey 

Secondary:

      335 V@ 150mA      Red

      0 V            Green/Yellow  

      335 V            Red   

      5 V@2A            Yellow

      0 V            Yellow

      3.15V@3A      Green

      0V            Green/Yellow

      3.15V            Green 

With a 5Y3WGTB (RT513) and idling current You get about 350V DC of B+, with a GZ34 (RT501)  it is about 390V

PT-Secondary: incl. 5V winding (for Rectifier)

Transformator Type: MainTransformer

Stack: 3.375 Inch

ON DEMAND! ESTIMATED DELIVERY FROM 4 TO 31 WORKING DAYS!

Transf.MAINS for: Fender® Tweed Deluxe Amp (5E3 etc.). 

NEW VERSION: 2" STACK and C.T. on filament for low noise

supports 6L6GC and GZ34/5AR4 tubes also! 

Lamination: 3 3/8"

Mounting on 70 x 56mm, lay-down. 

Height above chassis: 75mm

W x D x H: 87mm x 70mm x 90mm

weight: aprox. 2.2kg 

Primary:            

      0 V      Black

      230 V      White

      240 V      Grey 

Secondary:

      335 V@ 150mA      Red

      0 V            Green/Yellow  

      335 V            Red   

      5 V@2A            Yellow

      0 V            Yellow

      3.15V@3A      Green

      0V            Green/Yellow

      3.15V            Green 

With a 5Y3WGTB (RT513) and idling current You get about 350V DC of B+, with a GZ34 (RT501)  it is about 390V

PT-Secondary: incl. 5V winding (for Rectifier)

Transformator Type: MainTransformer

Stack: 3.375 Inch

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6AB4 is a miniature triode designed for use as a grounded-grid radio-frequency amplifier, frequency converter, or oscillator at frequencies below approximately 300 megacycles.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.rence only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12AL8 is a power tetrode, medium-mu 9-pin miniature for use in automobile radio receivers operated directly from 12-volt storage batteries.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6Y6GT is a beam power pentode primarily intended for use as an audio frequency power amplifier. It is particularly useful in applications where the available supply voltage is relatively low.

Also known by US military identifier VT-168A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 14Q7 is a pentagrid converter designed for use as a combined oscillator and mixer in superheterodyne receiver. The electrical characteristics of the 14Q7 are similar to those of the 12SA7. Except for heater rating, the 14Q7 is identical to the 7Q7.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6AV6 is a miniature duplex-diode, high-mu triode intended primarily for use as a combined detector, amplifier, and automatic-volume-control tube in radio receivers. The triode section incorporates a high amplification factor and is capable of providing a relatively large undistorted output voltage from a very small input signal. The 3AV6, 6AV6, and 12AV6 are alike except for heater ratings and heater-cathode voltage ratings.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12SA7GT is a pentagrid converter designed to minimize frequency drift. They are intended for service as combined oscillators and mixers in AC, storage battery, and AC/DC operated superheterodynes.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12SC7 is a twin-triode amplifier designed for use as an audio amplifier or phase inverter. Special shielding arrangement in the base permits operation at a low hum level.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6BH6 is a miniature sharp-cutoff pentode primarily designed for use as a high-gain radio-frequency or intermediate-frequency amplifier. Features include low grid-plate capacitance, relatively high transconductance, and low heater current.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6L7G is a mixer tube designed for service with a separate oscillator as the first detector in superheterodyne receivers. The control grid is of the remote cut-off type which allows the use of AVC and minimizes cross-modulation. The control grid is of the sharp cut-off type. The tube may be used as a volume expander or as a doubly controlled general purpose amplifier.

Also known by US military identifier VT-87A.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12AV6 combines a high mu triode and two independent diode units in the 7-pin miniature construction. It permits a single tube to function as detector, AVC rectifier, and audio amplifier. Coupling between the diode and triode sections is minimized by the use of internal shielding.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1LD5 is a diode-audio pentode designed especially for service as a combined diode detector and pentode audio amplifier. The diode plate is located at the negative end of the filament.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 12AB6 is a beam power tube of the 9-pin miniature type designed for use as the output amplifier in automobile radio receivers operating from a 12-volt storage battery. The 12AB5 can provide high power output because of its high power sensitivity and high efficiency. Design features of the 12AB5 include a large plate structure to allow for greater heat dissipation, a heater specially processed to withstand the severe operating conditions encountered during battery charging and discharging, and double base-pin connections for grid No. 1 and grid No. 2 to provide for cooler grid operation and greater flexibility of circuit connection.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 50EH5 is a miniature power pentode primarily designed for use in the audio-frequency power output stage of radio receivers and phonographs. The tube features high power sensitivity at low plate and screen voltages.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6BC8 is a miniature, medium-mu, semi-remote cutoff twin triode intended for application as a VHF cascode amplifier in a television receiver.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 77 is a triple grid general purpose detector amplifier.

Also known by US military identifier VT-77.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 6FD7 is a dissimilar section double triode intended to serve the combined functions of the vertical deflection oscillator and amplifier. It features the T-9 bulb with integral wafer base which fits the standard 9 pin miniature socket.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 8SN7GTB is a medium-mu triode intended for use as a combined vertical oscillator and vertical deflection amplifier in 450 mA. series heater operated television receivers. Thermal characteristics of the heater are controlled such that heater voltage surges during the warm-up cycle are minimized provided it is used with other types which are similarly controlled.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 0D3-A is a two-element gas filled, cold cathode voltage regulator. It is designed to provide a regulated output of approximately 150 volts. A jumper connected in the base between pins 3 and 7 provides the designer with several possible connections to ensure protection of associate components in case the regulator is removed from the socket. Except for bulb, this type is interchangeable with 0D3 tubes. Also known by US military identifier "VT-139", "VT-139/VR150-30"

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

ON REQUEST! ESTIMATED DELIVERY 5 TO 31 WORKING DAYS!

New-Old-Stock (NOS) tube.

The 1LN5 is a sharp-cutoff pentode designed for use as a radio-frequency, intermediate frequency, or audio-frequency amplifier in battery operated receivers.

Also known by US military identifier VT-179.

Note: brands may vary. Photo is for reference only and may not exactly represent final product received.

High Quality Tele style control plate made in South Korea. Slanted switch and also increased space between the switch and the volume pot. No trouble when turning the volume knob while the switch is in bridge position! Easier switching! Thickness: 1,6mm. Chrome.

Two-hole potentiometer control plate and pickup selector for almost every Telecaster USA & Mexico made from 1952 to present. Screws is not included.

Mini toggle switch DPDT ON-ON. With this mini switch you can do ‘series/parallel pickup switching’, ‘phase switching’ and ‘humbucker coil tapping’ to all guitars on the market.

This item has a higher quality than others in the same category due to the fact that better components have been used to manufacture it and the quality control has been more exhaustive, which makes it less prone to noise and has a longer life span.

Mini toggle switch DPDT ON-ON-ON. With this mini switch you can do ‘series/parallel pickup switching’, ‘phase switching’ and ‘humbucker coil tapping’ to all guitars on the market.

This item has a higher quality than others in the same category due to the fact that better components have been used to manufacture it and the quality control has been more exhaustive, which makes it less prone to noise and has a longer life span.

100% Genuine part for Fender Brian May, Jazzmaster, Jaguar guitars. DPDT (double-pole / double-throw), on / on switch has six lugs, three on each pole.