3 WAY CHROME TOGGLE SWITCH...
Three-position selector switch in chrome with black button or cap and made of plastic. This selector is very popular on Gibson or Epiphone made outside of the United States. The washer and nut are included.
Three-position selector switch in chrome with black button or cap and made of plastic. This selector is very popular on Gibson or Epiphone made outside of the United States. The washer and nut are included.
Comp Carbon Resistors with a tolerance of 5% at 0.5W. They have a low inductance and capacitance and are ideal for use in amplifiers or HI-FI equipment.
Sold in a pack of 5 units.
A black-gold double-pole 3-way switch, popular in guitars made outside the USA. Fits 2-pickup guitars. Knurled mounting nut, flat washer, and black, chrome and cream plastic knobs are included.
Dimensions:
Overall height is 2 "(50mm)
7/8 '(23.5mm) mounting depth with almost 3/8 "(9mm) threaded section.
Fits 1/2 "mounting hole diameter.
Excellent quality shielded and braided "Vintage" type cable to internally wire your Gibson guitar in the purest style of the 50's or 60's ("50's Wiring"). The cable can also be used to wire a combo or display or to make the typical old amp braided cable. Diameter is 0.070 "(1.78mm).
The best kit to avoid losing treble when lowering the volume of your guitar especially in single coil pickups! This kit is comprised of premium American-made electronic components: a 0.0012uF Sprague Orange Drop capacitor and a 130k 1 / 2W Allen Bradley resistor.
Excellent quality monofilar cables with BLACK cotton coating type "Vintage" and with a single conductor, to wire any brand of guitar or bass on the market: Fender , Gibson , Ibanez , Jakson, Rickenbacker ... The cable can also be used to wire a combo or display or to make the typical old amp braided cable. The diameter is .070 ".
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k split shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s.
Switchcraft mono end pin. 15/32 "dia. 1/2" mounting hole. For acoustic and active electronics guitars. Turns on battery when plug is inserted. With nut, washer and the brand Switchcraft serigraphed. MADE IN USA
Three-position selector switch in chrome with white button or cap and made of plastic. This selector is very popular on Gibson or Epiphone made outside of the United States. The washer and the nut are included.
Bourns brand potentiometer made for guitars (PDB181-GTR series) that have a very small gap or thickness. High quality with a tolerance of ± 20 %. A washer and a nut are included.
The 2-pole switch can be used in a Varitone notch filter circuit, per Gibson ES-345 guitars. Hardware included. Made by Alpha .
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k long shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender and Gibson started using them in the early '60s.
Excellent quality monofilament cables with RED cotton coating type "Vintage" and single conductor, to wire any brand of guitar or bass on the market: Fender , Gibson , Ibanez , Jakson, Rickenbacker ... The cable can also be used to wire a combo or display or to make the typical old amp braided cable. The diameter is .070 ".
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k split shaft pot. Linear taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs.
Potentiometer of the Alpha brand of the best value for money. Very accurate and durable.
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k split shaft pot. Audio (log) taper. This pot is ideal for instruments with single coils pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s.
Pickup Selector Trim for Gibson Black Guitars. They are brand new and unused.
ATTENTION: Cannot be used on Switchcraft brand position switches. If you are looking for a trim of this brand visit our store.
Authentic and genuine Switchcraft brand model # 11 jacks. Great for use on your Fender guitar or effect pedals, but can be used on amps without any problems. Very hard and resistant and with a quality proven for many years. Inside the jack, the manufacturer's brand is screen-printed and the washer and its corresponding nut are included.
Three-position selector switch in chrome with button or cap in ivory or cream and made of plastic. This selector is very popular on Gibson or Epiphone made outside of the United States. The washer and nut are included.
This Slovak-made vacuum tube is the perfect choice for quality and price for amps with a lot of gain and you want to have less (70% gain).
Before shipping it is tested with an Orange VT-1000 Vacuum Valve Tester!
Pickup selector trim for black Fender Telecaster guitars. They are brand new and unused.
ATTENTION: THIS COVER IS NOT VALID FOR THOSE GUITARS THAT USE SWITCHCRAFT OR FENDER MA RCA SELECTORS. IF YOU WANT ANY OF THIS MA RCA VISIT OUR STORE.
Potentiometer of the Alpha brand of the best value for money. Very accurate and durable.
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k solid shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Solid shaft for push-fit knobs.
Original Switchcraft brand switch (short size) for Gibson and Epiphone . This article will give you the sound and quality you are looking for for your guitar. Made in the United States and imported. The original Switchcraft white hood or hood is included.
Excellent quality single-core cables with 1 meter RED and 1 meter BLACK "Vintage" color cotton coating and single conductor, to wire any brand of guitar or bass on the market: Fender , Gibson , Ibanez , Jakson, Rickenbacker .. The cables can also be used to wire a combo or display or to make the typical stranded old amp cable.
Similar in function to the Fender "No Load" pot, the Emerson Pro Blender pot is an improvement to this design idea. Our Blender Pot acts as a true bypass when rotated between 9 and 10. The main difference from the "No Load" is that the Emerson Pro Blender pot does NOT have a detent, which means a no click feel between 9 and 10.
Excellent quality single-core cables with 1 meter WHITE and 1 meter BLACK "Vintage" color cotton coating and single conductor, to wire any brand of guitar or bass on the market: Fender , Gibson , Ibanez , Jakson, Rickenbacker .. The cables can also be used to wire a combo or display or to make the typical old amp braided cable.
Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter ± 8% resistance tolerance compared to CTS products offered by most other suppliers.
3-way selector made by the Electroswitch company in the United States, famous for its high resistance to use, almost 0% noise and its ease to solder the cables in it. This brand of selector has been around since the early days of the electric guitar and is the best you can find on the market today.
Pack of three meters of cable (one meter of each color) to use in all Gibson and Epiphone brand Epiphone ! Made in America since the 1950s!
Cart is empty