Added to the final invoice

3PDT push button with nine pins for "PCB soldering" for use in modifications and repairs that require this type of switches such as effects pedals, wah wah...

Measurements:

Length: 41mm
Width (with pins): 19mm
Thread shaft length: 12mm
Total shaft length: 22mm
Distance between pins: 5mm
Diameter: 9mm

ON REQUEST. DELIVERY IN 7-31 WORKING DAYS.

NOS (New-Old-Stock) tube. The 6KD6 is a compactron beam power pentode designed primarily for use as a horizontal deflection amplifier in colour television receivers. It is characterised by a very low knee with a very high peak current of over one ampere. This results in a basic capability to scan 90 degree large screen colour picture tubes at 25 kV from 280 volt power supplies. Its low knee minimises snivets without the need to supply special voltages to the beam plates.

Mica capacitors imported from the United States (USA).

Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k split shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s.

Mini toggle switch DPDT ON-ON manufactured by the Carling brand. With this mini switch you can make "series / parallel pickup switching", "phase switching" and "humbucker coil tapping" to all guitars on the market.

Authentic and Genuine Sprague Orange Drop 716P Series Capacitors Made in America. They are the condensers preferred by technicians around the world who repair vintage amplifiers from brands such as Fender , Ampeg , Magnatone, Marshall , Valco among many other brands.

Bourns brand potentiometer made for guitars (PDB181-GTR series) that have a very small gap or thickness. High quality with a tolerance of ± 20 %. A washer and a nut are included.
Measurements:

Total length from base to stem - 30mm

Screw-in shaft length - 11mm

Diameter length for the "Knob" - 10mm

Base diameter - 16mm

Rubber foot for heavy amplifiers, cabinets, effect pedals, dj's .... With steel insert. Diameter: 38mm. Height: 25mm. Hole diameter: 6.5mm. HIGH QUALITY FROM GERMANY!

Silicone rings ideal for valves that will prevent vibrations and noise.

Diameter: 40mm

ON DEMAND! ESTIMATED DELIVERY TIME BETWEEN 5 TO 31 DAYS.

Premium directly heated heavy duty rectifier Diode. Re-issue of the most popular rectifier valve ever built by Mullard. Helps extend the life of the other valves in the amplifier by allowing them to heat up before plate voltage is applied.

Low internal voltage drop & controlled heater warm up time

Excellent choice for both Hifi and instrument amplification

Replacement/upgrade for all 5AR4/GZ34 types.

New silicone rings ideal for valves that will prevent vibrations and unwanted noises.

20 high quality chrome pickguard screws, jack plates or backs for Fender Stratocaster, Telecaster and similar guitars.

Measures 3x12mm

Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 500k split shaft pot. Linear taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs.

The best kit to avoid losing treble when lowering the volume of your guitar especially in single coil pickups! This kit is comprised of premium American-made electronic components: a 0.0012uF Sprague Orange Drop capacitor and a 130k 1 / 2W Allen Bradley resistor.

New silicone rings ideal for valves that will prevent vibrations and unwanted noises.

Diameter: 20mm

The 2-pole and 3 position switch can be used in guitars. Hardware included. Made by Alpha .

Kit for Fender Telecaster model guitars with the highest quality on the market! All the components of this kit are made in the United States with the best materials to give it the highest quality, sound, a very long useful life and low noise.

Made in Russia. One of the best tubes you can buy for your amplifier or sound equipment now reissued by the New Sensor company. Excellent valve for its low noise level and couplings and for its musical details. Ideal to get a more British sound since, it reissues the vintage sound of the 60s quite clearly.

3PDT pushbutton with nine pins to "solder them to the air" for its use in modifications and repairs that demand this type of switches such as effects pedals, wah wah ...