Contacto
91-7728996
Horario
Lunes a Viernes: 09:00-13:45 y 15:00-16:30
Garantía de Devolución
durante 14 días
LINEAR 250K MN250K POT...
Pot for controlling one pickup or source to another, with both signals full at the center detent. Split shaft. Metric.
MINI POTENTIOMETER A250K...
Potenciómetro para bajos o guitarras ideal para cuerpos con poco grosor como las Ibanez o similares gracias a su eje largo. Medidas métricas para guitarras fabricadas en China, Japón, Corea del Sur, Indonesia...
B250K 250K LINEAR TAPER...
Potenciómetro de la marca Alpha versión mini especial para aquellas guitarras con poca profundidad o con poco hueco entre componentes y cables. También se puede usar en pedales de efectos o amplificadores. Esta marca lleva muchos años suministrando a los principales fabricantes de guitarra como Fender, Gibson, Ibanez y otras tantas para sus guitarras hechas fuera de Estados Unidos.
MINI POTENTIOMETER ALPHA...
Potenciómetro de la marca Alpha versión mini especial para aquellas guitarras con poca profundidad o con poco hueco entre componentes y cables. También se puede usar en pedales de efectos, amplificadores u otros aparatos musicales.
MINI POTENTIOMETER ALPHA...
Potenciómetro de la marca Alpha versión mini especial para aquellas guitarras con poca profundidad o con poco hueco entre componentes y cables. También se puede usar en pedales de efectos, amplificadores u otros aparatos musicales.
MINI POTENTIOMETER ALPHA...
Potenciómetro de la marca Alpha de lo mejor en relación calidad-precio. Muy precisos y duraderos.
POTENTIOMETER 250K B250K...
Potenciómetro fabricado en China. Sus medidas son ideales para aquellas guitarras fabricadas fuera de los Estados Unidos porque el diámetro del eje es menor, lo que hace que se encaje perfectamente en el agujero del golpeador o de la madera sin necesidad de limar. De fácil giro, se incluyen una arandela lisa, otra dentada y dos tuercas.
POTENTIOMETER 250K A250K...
Potenciómetro fabricado en China. Sus medidas son ideales para aquellas guitarras fabricadas fuera de los Estados Unidos porque el diámetro del eje es menor, lo que hace que se encaje perfectamente en el agujero del golpeador o de la madera sin necesidad de limar.
MINI POTENTIOMETER ALPHA...
Potenciómetro de la marca Alpha fabricado en Taiwán de la serie RV16AF ideal para guitarras o bajos aunque se puede usar también en pedales de efectos, mesas de mezclas... Sus medidas son ideales para aquellas guitarras fabricadas fuera de los Estados Unidos porque el diámetro del eje es menor, lo que hace que se encaje perfectamente en el agujero del golpeador o de la madera sin necesidad de limar.
POTENTIOMETER PARTSLAND...
Potenciómetro de la marca Partsland fabricado en Corea del Sur. Sus medidas son ideales para aquellas guitarras fabricadas fuera de los Estados Unidos porque el diámetro del eje es menor, lo que hace que se encaje perfectamente en el agujero del golpeador o de la madera sin necesidad de limar. De fácil giro, se incluye arandela y tuerca.
ALPHA POTENTIOMETER B250K...
Potenciómetro de la marca Alpha fabricado en Taiwan de la serie RV24AF ideal para guitarras. Sus medidas son ideales para aquellas guitarras fabricadas fuera de los Estados Unidos porque el diámetro del eje es menor, lo que hace que se encaje perfectamente en el agujero del golpeador o de la madera sin necesidad de limar.
POTENTIOMETER BOURNS 250K...
Potenciómetro de la marca Bourns fabricado para guitarras o bajos. Gran calidad con una tolerancia de ±20 %. Con un giro muy suave.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 24mm
BOURNS 250K DUAL SOLID...
Pot for controlling one pickup or source to another, with both signals full at the center detent. Audio or Linear Taper with split shaft.
POTENTIOMETER A250K 250K...
Acts as a normal volume or tone control, and pulls up to activate its on/on double-pole double throw mini switch. Controls pickup phasing, series/parallel switching and coil-taps- Split shaft with coarse knurling. One mounting nut and flat washer included. Measures metric for Japan, China or Korea Guitars!
BOURNS 250K A250K AUDIO...
Potenciómetro de la marca Bourns fabricado para guitarras (serie PDB181-GTR) que tengan un hueco o un grosor muy pequeño. Gran calidad con una tolerancia de ±20 %. Se incluye una arandela y una tuerca.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 16mm
CTS 250K A250K NYLON SHAFT...
Potenciómetro fabricado en Estados Unidos por CTS para su uso en la mayoria de marcas de amplificadores fabricados en Estados Unidos sobre todo en amplificadores Fender de la década de los 70. Su eje esta hecho de Nylon. Se incluye una arandela y una tuerca.
Medidas:
Longitud total - 26mm
Longitud del eje enroscable - 6mm
Longitud del eje en total - 16mm
Diámetro de la base - 23.5mm
BOURNS 250K A250K AUDIO...
Potenciómetro de la marca Bourns fabricado para guitarras (serie PDB181-GTR) que tengan un hueco o un grosor muy pequeño. Gran calidad con una tolerancia de ±20 %. Se incluye una arandela y una tuerca.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 16mm
BOURNS 250K B250K LINEAR...
Potenciómetro de la marca Bourns fabricado para guitarras (serie PDB181-GTR) que tengan un hueco o un grosor muy pequeño. Gran calidad con una tolerancia de ±20 %. Se incluye una arandela y una tuerca.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 16mm
BOURNS 250K MN250K DUAL...
Pot for controlling one pickup or source to another, with both signals full at the center detent. Audio or Linear Taper with split shaft.
POTENTIOMETER BOURNS 250K...
Potenciómetro de la marca Bourns fabricado para guitarras o bajos que tengan un hueco o un grosor muy pequeño. Gran calidad con una tolerancia de ±20 %. Se incluye una arandela y una tuerca. Con un giro muy suave. Serie PDB241.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 24mm
POTENTIOMETER BOURNS 250K...
Potenciómetro de la marca Bourns fabricado para guitarras o bajos. Gran calidad con una tolerancia de ±20 %. Con un giro muy suave.
Medidas:
Longitud total desde su base hasta el vástago - 30mm
Longitud del eje enroscable - 11mm
Longitud del diámetro para el "Knob" - 10mm
Diámetro de la base - 24mm
CTS LINEAR 250K POT...
Potenciómetro fabricado por CTS en Estados Unidos ideal para tipo de bajos y guitarras del mercado (si tu guitarra es de fuera de Estados Unidos tendrás que limar el golpeador o la madera para que pueda encajar el eje ya que su diámetro es de métrica americana).
BOURNS AUDIO A250K 250K...
Acts as a normal volume or tone control, and pulls up to activate its on/on double-pole double throw mini switch. Controls pickup phasing, series/parallel switching and coil-taps- Split shaft with coarse knurling. Two mounting nuts, flat washer and lock washer included.
CTS LINEAR 250K POT...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k solid shaft pot. Linear taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Solid shaft for push-fit knobs.
CTS AUDIO LOGARITHMIC 250K...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k solid shaft pot. Audio or log taper. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Solid shaft for push-fit knobs.
CTS POTENTIOMETER 250K...
CTS pots with a shorter ¼” bushing length that is perfect for pickguard mounted pots. These pots reduce the gap between the pickguard and bottom of the knob for a clean, near flush look. The shaft is a fine (24 tooth) knurl. Nut and lock washer are included.
250K CTS LONG SHAFT...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250K long shaft pot. Audio (log) taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender and Gibson started using them in the early '60s. Split shaft for push-fit knobs.
250K CTS LONG SHAFT...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250K long shaft pot. Linear taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender and Gibson started using them in the early '60s. Split shaft for push-fit knobs.
CTS LINEAR 250K POT...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k split shaft pot. Linear taper. This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs.
CTS TAD 450GT 250K B250K...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k solid shat shaft pot. Linear taper. This pot is ideal for instruments with single coils pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs. Each CTS pot includes a lock washer and one hex mounting nuts for custom height adjustment on a pickguard or control plate.
PREMIUM CTS POT...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k split shaft pot. Audio (log) taper. This pot is ideal for instruments with single coils pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s.
BOURNS AUDIO 250K PUSH/PULL...
Acts as a normal volume or tone control, and pulls up to activate its on/on double-pole double throw mini switch. Controls pickup phasing, series/parallel switching and coil-taps- Split shaft with coarse knurling. Two mounting nuts, flat washer and lock washer included.
CAUTION: In some Les Pauls, this potentiometer can be very large.
1x EMERSON PRO CTS 250K 8%...
Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter ±8% resistance tolerance compared to CTS products offered by most other suppliers.
EMERSON PRO CTS 250K 8%...
Emerson Pro CTS pots from Emerson Custom were designed to be the premium choice for the discerning guitarist looking for the optimum performance and tonal response from a guitar potentiometer. These specially designed Emerson Pro CTS feature a longer-life brass shaft and bushing. They also feature a tighter ±8% resistance tolerance compared to CTS products offered by most other suppliers.
CTS 250K A250K DPDT...
The best push-pull potentiometer ever made! These aren't your standard off the shelf CTS pots either. Mojotone had them custom made to their specification to have the smoothest taper possible and the tightest tolerance available!
GENUINE PREMIUM CTS MINI...
Guitar volume and tone pot - the top-of-the-range 450 series CTS Premium 250k split shaft pot. Audio (log) taper. This pot is ideal for instruments with single coils pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs.
CTS 250K REVERSE LOG AUDIO...
Guitar and bass volume and tone pot. Audio (REVERSE log) taper for LEFT HAND (SOUTHPAW). This pot is ideal for instruments with humbuckers pickups. CTS pots have been used in countless electric guitars since Fender started using them in the early '60s. Split shaft for push-fit knobs.
AUDIO/LOG 250K PUSH-PUSH...
Potenciómetro "Push-Push" que te permitirá hacer múltiples variantes en tus pastillas Humbucker (coil tapping, splitting, and phasing). Las especificaciones son para guitarras americanas pero se puede usar de otros países limando la madera o golpeador para que el diámetro del eje encaje.
LINEAR 250K PUSH-PUSH...
Potenciómetro "Push-Push" que te permitirá hacer múltiples variantes en tus pastillas Humbucker (coil tapping, splitting, and phasing). Las especificaciones son para guitarras americanas pero se puede usar de otros países limando la madera o golpeador para que el diámetro del eje encaje.
CTS DUAL 250K BLEND-BALANCE...
Potentiometer by CTS (USA) for controlling one pickup or source to another, with both signals full at the center detent. Linear Taper with split shaft.
Measures:
3.7cm X 1.7 cm
1x EMERSON PRO CTS 250K...
Similar in function to the Fender "No Load" pot, the Emerson Pro Blender pot is an improvement to this design idea. Our Blender Pot acts as a true bypass when rotated between 9 and 10. The main difference from the "No Load" is that the Emerson Pro Blender pot does NOT have a detent, which means a no click feel between 9 and 10.
FENDER 250K/500K STACKED...
Two potentiometers in one for you Fender Jazz Bass reissue o Telecaster designed by CTS! Stacked design allows you to have two volumes, or two tones or a volume and a tone combination in one mounting hole!. ATTENTION! the top / volume section is 500K and the bottom / tone section is 250K
3/8" mounting hole. Top shaft is 3/16"(4.75mm) diameter and bottom shaft is 17/64"(6.75mm) diameter.